WOW !! MUCH LOVE ! SO WORLD PEACE !
Fond bitcoin pour l'amélioration du site:
1memzGeKS7CB3ECNkzSn2qHwxU6NZoJ8o
Dogecoin (tips/pourboires):
DCLoo9Dd4qECqpMLurdgGnaoqbftj16Nvp
Rechercher sur le site:
Home
|
Publier un mémoire
|
Une page au hasard
Memoire Online
>
Sciences
Thème: simulation d'un train de traitement de gaz à l'aide des outils HYYSYS et PRO II
( Télécharger le fichier original )
par
Abbes Gouri
Ecole nationale supérieure polytechnique - ingénieur en génie chimique 2009
Disponible en
une seule page
suivant
Remerciement
Glossaire
Liste des abréviations
SOMMAIRE
Liste des figures
Liste des tableaux
Introduction
Chapitre I:
Généralités sur le traitement et le
fractionnement du gaz à condensât
I.1.Généralités
I.2. Séparation des condensats
I.3.Opérations de purification
I.3.1. Absorption par un solvant
I.3.2. Perméation gazeuse
I.4. Déshydratation
I.4.1. Déshydratation par adsorption
I.6. Fractionnement des condensats
I.6.1. Fractionnement par réfrigération
I.6.1.2. La détente isentropique
I.7. Description des procédés de traitement de gaz
I.7.1. Le procédé PRICHARD
I.7.2. Le procédé HUDSON
I.7.2.1. Principes thermodynamiques de la vanne Joule-Thomson
I.7.2.2. Principes thermodynamiques du turbo-expander
Chapitre II :
Présentation du champ du Gaz
GTFT
II.1.Situation géographique
II.2. Développement et capacité du champ:
II.2.1.Roche mère et genèse des hydrocarbures :
II.2.2.Description du réservoir:
II.2.3. Historique de production:
Chapitre III:
Description du procédé du traitement du
Gaz GTFT
III.1.1. Section de refroidissement et séparation primaire :
III.1.1.1. Refroidissement :
III.1.1.2. Séparation primaire :
III.1.2. Section de déshydratation :
III.1.2.1. L'adsorption :
III.1.2.2. La régénération :
III.1.3. Section de refroidissement et de détente:
III.1.3.1. Le refroidissement :
III.1.3.2. La détente:
III.1.4. Section de fractionnement :
III.1.4.1. Le déethaniseur :
III.1.4.2. Le stabilisateur :
III.1.4.3. Le débutaniseur :
III.2.1. Rappel thermodynamique sur la compression
III.2.1.1. Détermination de la température polytropique en fin de compression
ChapitreIV:
Simulation
IV.1. Présentation des simulateurs PRO II et HYSYS
IV.1.1. Définitions
IV.1.2. Modèle thermodynamique?
IV.1.3. Les simulateurs HYSYS et PRO II :
IV.2. Choix du modèle thermodynamique
IV.2.1. Utilisation du facteur de compressibilité
IV.2.2. Utilisation des équations d'état :
IV.2.2.1. Equation de Van der Waals (1872) :
IV.2.2.2. Equation de Redlich-Kwong(1949)
IV.2.2.3. Équation de Peng-Robinson (1976)
IV.2.3. Etendue d'utilisation des équations d'état
IV.2.4. Recommandations des modèles
IV.2.5. Choix d'un modèle thermodynamique
IV.3. La simulation d'un train de traitement de gaz GTFT:
IV.3.1. Le cas design
IV.3.2. Le cas actuel
IV.3.3. La baisse de pression (sans Boosting):
IV.4. Simulation d'un train de traitement de gaz avec l'intégration de Boosting
IV.4.1. Le reflux du stabilisateur :
IV.4.1.1. Scénario 2012
IV.4.1.2. Scénario 2015
IV.4.2. L'échangeur E2-1208 :
IV.4.3. La boucle d'huile du rebouilleur E4-1402 :
IV.5. Etude technico économique du projet Boosting
IV.5.1. Les critères de choix d'un investissement
IV.5.1.1. La valeur actuelle nette (VAN)
IV.5.1.2. Le taux interne de rentabilité (TIR : r)
IV.5.2. Etude de la rentabilité du projet Boosting
IV.5.2.2. Calcul du TIR
Conclusion
Références bibliographiques
Annexe A
A.2 Diagramme de circulation de fluides PFD (avec Boosting)
A.5 La boucle du fluide caloporteur
G.P.L.
Annexe B
Manuel d'utilisation de HYSYS
suivant
Rechercher sur le site:
"Soit réservé sans ostentation pour éviter de t'attirer l'incompréhension haineuse des ignorants"
Pythagore